Medical Waste Transporter

The material of the medical waste transport vehicle produced by Hubei Chengli Special Purpose Vehicle Co., Ltd. is made of external glass steel, stainless steel plate, ultraviolet sterilization lamp, and spray disinfection device. Double-opening the back door, with a fixed horizontal ring in the compartment and a circular transition in the inside corner. Standard minus 5 degree refrigeration unit. There is no leakage in the seal of the entire vehicle body, ensuring that the medical device does not breed bacteria on the way of transportation.

Chassis configuration: single-row cab, JAC Isuzu States four horsepower diesel engine 120, 7.00 steel tire, air brakes, fifth gear box, factory air conditioning, the rear axle 5 tons, the direction of power.

Standard configuration: box size length × width × height: 4130 × 1810 × 1700 , 12.7 cubic meters , the thickness of the car body is 8 cm. The outer plate is made of special fiberglass for refrigerated trucks, the inner material is stainless steel (reflects sunlight), the middle layer is polyurethane foam insulation material, (fireproof flame retardant insulation) is pressed by a large-scale 10,000-ton press , and the configuration box is all Stainless steel locks, stainless steel corners, stainless steel door frames, ceiling lights and bumpers. Our factory's medical waste transfer vehicle thermal insulation materials use imported grade XPS, water absorption rate ≤ 1, thermal conductivity ≤ 0.028W/mk, compression pressure ≥ 150Kpa, density 30 ~ 45kg/m3, use the world's most advanced fifth-generation fully enclosed Polyurethane plate adhesive structure, carton surface materials are glass steel, stainless steel, aluminum alloy, color steel plate and other materials to choose from, after molding the car body has the advantages of light weight, high thermal insulation coefficient, strong impact resistance, no leakage, etc. Atmosphere, water and acid, alkali, salt and other media have good corrosion resistance and aging resistance. By optimizing the design, the center of mass of the vehicle is reduced and the effective volume is increased. After testing, the comprehensive energy-saving rate of the vehicle and its service life is 1 to 2 times higher than that of a general refrigerated and insulated vehicle.

  Refrigerating unit: adopts Xinxiang Huatai or Xiangyang Hanxue-5 degree refrigeration unit, which has good cold storage effect, fast cooling, and the minimum temperature can reach 0 degrees to minus 5 degrees. It can be adjusted freely according to the demand.

This vehicle is specially designed according to the characteristics of medical waste, and it adopts airtight transportation. The back door is double sealed and uses a labyrinth seal to completely close the carriage so as to prevent the spread of toxic gases from medical waste bacteria. The body of the vehicle has a UV disinfection function. When the UV lamp works normally, it radiates a large amount of ultraviolet rays of 253.7 nm , which is extremely powerful against microorganisms and kills bacteria within 30-45 minutes. The product has closed, impervious, dust-proof properties; antibacterial, fire-retardant, corrosion-resistant, easy cleaning and disinfection functions. According to the “Regulations on Medical Waste Management”, medical waste transfer vehicles must use special vehicles with “medical waste” signs and environmental protection requirements. Sterilization of medical waste transfer vehicles: Anti-virus at low temperature, anti-virus by ultraviolet light and anti-virus by spray of drugs.

60Mn material Hot Rolling Ball have very good wear resistance and not broken, breakage is lower than 1%, and it have high impact value. Jinan Zhongwei 60Mn hot rolling ball have the advantage of large output, stable quality. Our 60Mn Hot Rolling Grinding Ball in the size ranging from 20mm to 60mm, which chemical composition: C:0.55-0.65, Si:0.17-0.37, Mn:0.7-1.0, Cr:≤0.25, P:<0.04, S:<0.04, and Hardness is 57 to 63HRC, mainly used to mining, cement plant and thermal power station.

60Mn Hot Rolling Grinding Ball

Grinding Steel Ball,60Mn Grinding Steel Ball,60Mn Grinding Ball,60Mn Hot Rolling Grinding Ball

Jinan Zhongwei Casting And Forging Grinding Ball Co.,Ltd , https://www.cngrindingballs.com