The curved road is not easy, the old driver has

Cars often run on the road, what kind of road conditions did not experience, roads and roads, narrow roads, narrow roads, straight roads, which are all roads. One of the most tested technologies is probably running detours, and it is still a bit difficult to drive without corners, especially some novice drivers. But don't worry, you have old drivers.

High speed cornering

If you want to take a short-hand turn on a high-speed road, try to drive the car on the inside as you enter the corner. When you exit the corner, try to drive the car on the outside to change the arc of the car and delay the curvature of the turn. This will effectively reduce the centrifugal force. Turn easily in case of deceleration.

Fog and sand bends

Drivers must be aware of how to drive a turn in this kind of weather. Turn on the front lights and fog lights as soon as possible and press the horns to make pedestrians and other vehicles pay attention. Slowly advance and prepare for stopping the brakes at any time. .

Rain and snow crossing corners

The most important thing in turning on rain, mud and mud is to pay attention to tire slipping, so be sure not to hit the steering wheel or brake hard. In addition to demanding themselves, we must also pay attention to the danger of slipping on other vehicles.

Uphill corner

For an uphill curve, the throttle should be sent before entering the curve, allowing the vehicle to enter the curve at a faster speed against the outside of the curve, and then reducing the gear by one or two gears, and then selecting the route and correcting the direction. Tap the throttle; after crossing the arc top of the curve, cut back to the outside of the curve. After confirming the safety of the road conditions, increase the throttle, and then quickly exit the curve by the outside of the curve.

Downhill bends

When passing through a downhill curve, the accelerator pedal should be sent before entering the curve to allow the vehicle to decelerate significantly, and to reduce the gear position by one or two stops, and then enter the bend at a slow speed against the outside of the curve. Road, and then send the brakes to select the route and correction direction; after crossing the curve of the top of the arc, then cut back to the outside of the curve, while tapping the throttle, and finally quickly out of the curve on the outside of the curve. In this process, the turning route should also be selected from the anterolateral posterior medial side.

The above is the trick to go through various corners. If you are still not familiar or dare to turn, you must remember to maintain a good speed, and turning slowly can avoid uncontrollable speed.

Excavator Engine Part

Excavator Engine Part

Excavator Engine Part System

1. Engine Cooling System

Store Enough Water, Make Circulating Water, Controlling Water Temperature , Lose Excess heat
Composition : From radiator, water pump, cylinder body watercourse, cylinder cover watercourse, out Water pipes, thermostats, water filters, medium coolers, oil coolers, and options, It consists of air compressor, hydraulic oil cooler, wet exhaust pipe, etc

Cummins Engine Parts 3076489 Thermosta For Excavators

2. Engine Fuel System

Engine Fuel System Have 2 Kind , One mode is High Pressure Injector System , One model is PT Fuel Injector System . The basic structural form of PT fuel system: it consists of fuel tank, fuel filter, PT fuel pump, low pressure oil pipeline, Fuel injector, rocker arm, push rod, oil injection CAM and return tubing.Among them: PT fuel pump also includes: gear pump, magnetic filter, pulse diaphragm damper, bipolar governor, throttle shaft, electromagnetic valve, etc. Many engines have special requirements for PT pumps, such as increasing the VS (full-course) governor, AFC smoke limiter, EFC electronic governor, ASA air signal attenuator .

PT(G)--VS--(AFC) Fitting On Bulldozer ,Marine, Trucks Engine

PT(G)--AFC Fitting On Bus and Cars Engine

PT(G)--EFC Fitting On Generators and Gun-set Engine

PT(G)-VS Fuel Injector Pump For Bulldozer Engines

3. Engine Lubricating System

Fuctions : It is very important for the reliability and durability of diesel engine to transport the lubricating oil with proper viscosity to all necessary parts .

Reduce wear and tear of parts and reduce friction work .
Cool and clean the lubricating surface .
Anti - rust effect on oil film adsorption .
Provide hydraulic medium .
Constitute : Oil pan, oil pump, oil cooler, Cooling piston nozzle, oil pipeline, pressure regulating valve, full flow oil filter, side, Pass filter and other components composition.

Another Excavator Parts We also Supplied.
Excavator parts: Excavator engine part, Excavator Undercarriage Parts, Excavator Final Drive, Excavator Main Valve , Excavator Hydraulic Pump.

Excavator Engine Parts,Excavator Spare Part,Komatsu Excavator Spare Parts,Yundai Excavator Spare Parts

Jining Kunpeng Construction Machinery Equipment Co., Ltd , https://www.excavatorenginepart.com