Friction press

A 【Friction Press】 Introduction 1. The J53 series double disc friction press is a forging press that uses a screw mechanism to transfer energy and eventually deforms the work. Suitable for hot stamping of metal and its alloys and stamping, correction, embossing, bending, and ceramics, cold pressing, cutting of ceramics, tableware, and refractory materials. 2. In addition, due to the unique force and energy characteristics of the screw press, it can meet a variety of process needs, that is, it can pay more forging energy and have a certain forging force, and can meet the process requirements of small forging force and forging energy. Better process adaptability.

3. A traditional structure of a double disc friction press is characterized in that the flywheel is driven by a friction mechanism. The drive chain of the machine consists of a belt drive, an orthogonal disk friction drive and a screw slider mechanism.

4. The double disc friction press has the characteristics of simple structure, large energy, low noise, long life, safety and reliability, and convenient use and maintenance. Widely used in aviation, automobiles, tractors, tool manufacturing, textile machinery and other industries.

Two [friction press] operating tips (a) seriously before work:

1, check the mold should be installed correctly, fastened firmly. The resultant center of the stamping part should coincide with the press center as much as possible. The die support area must not be less than one-third of the punch bottom area.

2. Clean the punch stroke space and mold space debris.

3, after empty test run or change the mold or adjust the height of the closure, the first stroke of the punch, only the use of manual rotation of the flywheel. Check and confirm that the mold closing height and the position of the screw are adjusted before starting the equipment.

4. The flywheel and the clutch must be disengaged to start the main motor. The direction of rotation of the flywheel must be the same as the direction of the flag.

(II) Work seriously:

1. Absolutely prevent parts from overlapping processing. Before parts and remnants are removed, feeding is strictly prohibited.

2. When the slider is running, it is not allowed to reach into the mold space to correct or take and place the parts.

3, always pay attention to the status of the mold, such as the discovery of loose or parts of the phenomenon of burrs increase, should immediately stop the inspection, troubleshooting and then continue to work.

(3) After the work, the flywheel and the clutch are disengaged, and the punch stops at the top dead center position.

Three [double disk friction press] maintenance of the four methods below to give you an introduction to the four major methods of press maintenance:

1. Pay attention to safety during the maintenance process, ensure that the locking/opening process is performed correctly to ensure the safety of maintenance personnel, and ensure that the sleeve is placed at the bottom of the stroke before performing brake maintenance work. If this is done, there is no need to lock the sleeve again.

2. In the workshop environment, a clean press allows operators or maintenance personnel to quickly find out when problems occur. Such as oil leaks, leaks, breaks, etc. If the press is clean, it is easy to find out where it is.

3. The electrical work is left to the relevant professionals to solve, only qualified electrical technicians can carry out electrical line maintenance of the press, but you can still check the lamp on the control panel of the press is normal, every class must ensure The light bulb is working and correctly shows the various operating conditions performed by the press.

4. To ensure that the press is in a balanced position, a press that is precisely balanced can work better, so it is best to check it once a year. Pneumatic systems are responsible for the operation of pneumatic brakes and balancing systems. They need to check for gas leaks, because proper air pressure can affect the performance of the brakes and balancing system, and they control the stopping time of the press. Once a problem occurs, it will cause the operation. And equipment are in danger. In addition, all pneumatic systems have regulators, lubricators and reservoirs. The water accumulated in the gas line should be removed every day.

Four 【Friction Presses】 Use the following three major precautions The following are three major considerations for press use:

1. In the workshop environment, a clean press allows operators or maintenance personnel to quickly find out when problems occur. Such as oil leaks, leaks, breaks, etc. If the press is clean, it is easy to find out where it is.

2. The electrical work is left to the relevant professionals to solve, only qualified electrical technicians can carry out electrical line maintenance of the press, but you can still check the lamp on the control panel of the press is normal, every class must ensure The light bulb is working and correctly shows the various operating conditions performed by the press.

3. To ensure that the press is in a balanced position, a press that is precisely balanced can work better, so it is best to check it once a year. Pneumatic systems are responsible for the operation of pneumatic brakes and balancing systems. They need to check for gas leaks, because proper air pressure can affect the performance of the brakes and balancing system, and they control the stopping time of the press. Once a problem occurs, it will cause the operation. And equipment are in danger. In addition, all pneumatic systems have regulators, lubricators and reservoirs. The water accumulated in the gas line should be removed every day.