Finishing the line is an important part of the construction of the weak motor room. Why should the line be sorted out, because it is better to have a corresponding port during the later maintenance. This is the ultimate goal of a neat route.
Evaluating a worker's level of integrated wiring is also mainly due to his proficiency, importance, clarity, and cleanliness.
Tools: cable clamp, cable organizer, cable management frame, bridge holder, line card, cable tie, tape, crystal head and wire processing equipment.
Especially important: label paper.
Â
basic method:
1, can use the line tool, do not use your hand.
2, the crystal head and the network cable connection port, must be seamless.
3, can use the line card, do not use cable tie.
4, the label should be laid.
Trace skills:
How to go well in the cabinet wiring, a large part of it has been decided in the cabinet structure design stage. The general cabinet wiring, there are the following tips:
1. Use the cable rack. The cabinet cabling is white. It is a 1U or 1SU sheet metal part with N teeth. The length of the teeth is long and short, depending on the size of the network equipment and the turning radius of the cable used.
2. Use a line bridge. The so-called line bridge is a radius-like structure that protrudes in the cabinet like a small bridge. It can be understood as the place where the cable can protrude from the cabinet board. The general line bridges will appear in the following places: the sub-cabin partitions of the cabinet, the columns, and the square hole strips of the installation equipment panels.
3. Use a reel. This is the same as the cable management frame and is generally used for fiber finishing of communication equipment.
4, flexible use of the (walking) spool. The so-called "walking" bobbin refers to the place on the subdivision partition when the lanes need to be routed in different subdivisions. The general entry (travel) spool appears in two compartments that need to be isolated from each other, such as between the equipment compartment and the battery compartment.
5. Use cable ties and labels. This is also mentioned in the basic method. It is very important that the cable tie is simple and flexible to use, and the label makes it easy to identify after the wiring and reduces the difficulty of maintenance.
And the most important thing: you need a reliable construction team.
We introduce ourselves as the leading manufacturer of Cylinder
Liners, cylinder head ,Piston Crown ,Piston Skirt ,valve stem,Valve Seat ,valve
housing etc. since last 25years in China.
if you are having any inquiry
regarding the products, please send us at your earliest.
and it is it
is full range of the cylinder head for the following type :
AAA) YANMAR DIESEL ENGINE
K(D)L,
KFL-T, 6MAL-H/T/HT/DT, S165-T/ST/EN,
S185-ST/UT/ET, M200L-UN/SN/EN/M220L-UN/SN/EN / N 330
BBB) DAIHATSU DIESEL
ENGINE
PS22/26/ DS18(A)/ DS(B)22/
DL20/22/28/ DK20 / DK 28
CCC) NIIGATA DIESEL ENGINE
6L(M)25BX/6M28AFTE/BX/6M31X/EZ/EX
DDD) AKASAKA
AH30/AH38/
AH40/D/F/ A31/34/37/41/ DM28/30/33/36/38/40(A)K/ DM46/ UEC37H-HB/ UEC
37/88H
UEC 37LA/ UEC45LA/ UEC52LA/ UEC52HA/ UEC60HA/ UEC60LS/ UEC45HA/115 ALL UET TYPE
EEE) MITSUBISHI (KOBE AND AKASAKA
)
45/75C/
45/80D/ 52/90D/ 52/105D.E/
UEC37H-IIB/ UET37/88HA/UEC45HA.LA/ UEC52HA.LA/ S6B/
ETC
FFF) HANSHIN
6LU(D)26/
6LU(N)28A/
6LU(D)32/6LU(D)35/
6LU(S)38/ 40 / 6LU40/ 6LU46A/
6LU50A/
6EL30/
EL(S)32 /6EL(S)35/ 6EL38/ 6EL40/ 6EL(S)44/50A/
GGG) MAN B&W
L35MCE/L50MCE/
L60MCE/ 40/54A
HHH) MITSUBISHI
PURIFIER
SJ700~SJ1800/SJ 2000
III)SULZER
RND 68 RND 76 RD 44
JJJ) MAKITA
GSLH –
633 637 KSLH -633
637
Kkk) PIELSTICK
PC
2-5 PC
2-6
Engine Cylinder Head
Engine Cylinder Head,Cylinder Head Gasket,Diesel Cylinder Head,Cylinder Head For Shipping
ZhouShan HeCheng Machinery Co., LTD. , http://www.hcmarineparts.com