PTFE Mesh Conveyor Belt for Food Process Belt
1. PTFE Mesh Conveyor Belt
2. Heat resistant, Microwave safe
3. High drying efficiency
4. Non-toxic & non-stick
5. Great tensile strength
PTFE Coated Fiberglass Mesh Conveyor Belt
PTFE Coated Fiberglass Mesh Conveyor Belt is ideally suited for conveying products within highly efficient air distribution systems allowing optimised moisture removal to take place and is commonly used within ultra violet and infra red dryer units
The open area allows maximum air flow optimising drying times whilst its extreme properties make it a natural choice for dryer manufactures.
Applications
PTFE Coated Fiberglass Mesh Conveyor Belts are used in applications such as the drying of printed products for example; Point of display stands, T-shirts, glass and mass produced paper prints. Print dryers usually opt for Ultra violet, Infra red or hot air as the heat source to dry.
Other applications range from the drying of cereals, non woven's, charcoal interlinings, carpet & carpet tiles, printed circuit boards and shrink-wrap tunnels but to name a few.
Features & Benefits
PTFE open mesh conveyor belting is light weight and cost effective therefore is easy to handle and less expensive than wire alternatives that can be difficult to replace. Often supplied with a metallic clipper type fastener these style of belts can easily be removed and replaced therefore minimising downtime and saving money. This material can be offered in carbon loaded black therefore providing antistatic properties.
Material Properties
· Temperature resistance: -70° C up to plus 260° C
· Chemical Inertness
· Ultraviolet, Infra-red, microwave, radio frequency resistance
· Non-Stick surface
· Lightweight and energy efficiency for economical operation
Additional Information
4x4 open area mesh is available in widths up to 4000mm wide and can be supplied at any length required. In addition film, glass or kevlar can be applied as edge reinforcement depending of the environment it will be used within. There are various methods of joining screen-printing belts however the metallic clipper or spiral types are more typical
Self-aligning ball bearings Include two rows of balls, the cage, the inner ring, and the outer ring with a common concave sphered raceway. Self-aligning Ball Bearing have a sphere raceway in the outer ring and a double raceway in the inner ring. This feature give the bearings their self-aligning property, permitting angular misalignment of the shaft relative to the housing. Ball bearings are therefore particularly suitable for applications where misalignment can arise from errors in mounting or from shaft deflection. Double row self-aligning ball bearings are mainly used to carry radial loads and light axial loads, but cann't carry pure axial loads.
Feature:
Mainly bear radial load, and can bear smaller axial load. Axis (shell) axial displacement limit in the clearance limits, the heart performance is automatically adjusted, normal work allows the inner and outer relatively small tilt conditions, suitable for bearing hole can not strictly ensure the concentricity. Self-aligning ball bearings are consequently self-aligning and insensitive to shaft deflections and angular misalignment of the shaft relative to the housing, It is particularly suitable for applications where considerable shaft deflections or misalignment are to be expected.
Self-aligning ball bearings have a common sphered raceway in the outer ring. This feature allows angular misalignment of the shaft relative to the housing. Therefore self-aligning ball bearings are particularly used in case of bearings where misalignment can occur from errors in mounting or from shaft bending.
Types:
Retainers are mainly made of steel sheet, synthetic resin, nylon etc. Its feature is the outer ring raceway spherical surface and automatical adjusted, so it can compensate for the deviation caused by different axial angle.
Nylon Cage ATN Self-aligning Ball Bearing
Iron Cage Self-Aligning Ball Bearing
Main Application
Owning to its specific structure, the self aligning ball bearing can be used in some relative field and some general lines.For example, Self-Aligning Ball Bearing applies to carry heavy load and impact load. Mine machine, port hoisting machine, port transfer equipment.
Professional mass production Bearing For Conveyor, With more than 10 years of Conveyor Bearing experience, we can assist you with selecting the appropriate bearings for your system. Welcome to visit our Factory. If you have any questions, please contact with us directly.
Self-aligning Ball Bearing
Self-Aligning Ball Bearing,Stainless Steel Self-Aligning Ball Bearing,Cheap Self-Aligning Ball Bearing
Shandong Xinkaite Bearing Co., Ltd. , https://www.idlerbearing.nl